Baller vtjc Posted June 12, 2022 Baller Share Posted June 12, 2022 I am preparing to replace the original dual Garmin pucks on my 2008 Ski Nautique 196 with the ECI single puck. I have reviewed Freddy’s videos. Where on the bow have people placed the single puck on a TSC3 hull? Is it possible to cover up the hole from the original Garmin puck? Any other lessons learned from this upgrade? I am thinking I will use a 1” hole saw to drill the hole and bevel the edges with a stone grinding wheel. Thanks in advance for your advice and input. OE Garmin Location 2 Location Options A & B Link to comment Share on other sites More sharing options...
Baller thager Posted June 12, 2022 Baller Share Posted June 12, 2022 If it were mine, I would drill out the original hole on one side and leave the other puck alone. That puck also could be used for a gps speedo. Link to comment Share on other sites More sharing options...
Baller_ Jody_Seal Posted June 12, 2022 Baller_ Share Posted June 12, 2022 A, and get as close as you can to the grommet hole. the bigger receiver should cover over the hole. just make sure the receiver is mount with arrow pointed forward. Link to comment Share on other sites More sharing options...
Baller LeonL Posted June 13, 2022 Baller Share Posted June 13, 2022 On my install I was able to cover the hole completely (after enlarging for the plug) no problem. (Your "A" location) As mentioned by @thager I just left the port side puck. Freddy's video is somewhat confusing as far as connections go. The new harness is a jumper, if you will, between what you unplug from the old setup. Should be common sense, but he confused me by saying plug in only one end, or something like that. Link to comment Share on other sites More sharing options...
Baller markn Posted June 13, 2022 Baller Share Posted June 13, 2022 This is where Skip Dunlap placed mine on our 2004 Limited. However, the old single pucks were installed using velcro, so no holes on the deck. Link to comment Share on other sites More sharing options...
Baller LeonL Posted June 13, 2022 Baller Share Posted June 13, 2022 @markn no holes? Where did the wires go? Link to comment Share on other sites More sharing options...
Baller markn Posted June 13, 2022 Baller Share Posted June 13, 2022 @LeonL In that my boat was pre-Zero Off, the antenna wires were run through the air in-take vents directly below the windshield. Jody S. did the original ZO conversion way back in 2009. Still works perfectly. Both Skip and Jody know inboards!! Link to comment Share on other sites More sharing options...
Baller vtjc Posted June 14, 2022 Author Baller Share Posted June 14, 2022 Thanks for the advice. I will move forward with location A having the new puck covering the OE hole. @thager the mount is off center and will be on the port side of the puck with the arrow facing forward so I don’t think it is possible to utilize the exact location of the OE hole. Another related thread: https://forum.ballofspray.com/discussion/18494/zero-off-single-puck-install-any-advice/p1 Link to comment Share on other sites More sharing options...
Baller thager Posted June 14, 2022 Baller Share Posted June 14, 2022 @vtjc I did not mean to center it on original hole but to cut hole with hole saw as jody_Seal described. Make a paper template of the puck first to make sure it will fit. If you drill hole forward and towards center of boat keeping original hole in the 1" hole saw diameter it sure looks like it should fit. Link to comment Share on other sites More sharing options...
Baller LeonL Posted June 15, 2022 Baller Share Posted June 15, 2022 You won't have any problem covering the hole. Just exercise normal diligence. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now