Baller matt_b Posted July 28, 2020 Baller Share Posted July 28, 2020 Just curious how long people are getting out of these boots? I love them and this is my 2-3rd pair but after 2 seasons of average use I need to start zip tying them together around the back side where the rubber meets the material. I always remove the liners and kept indoors during the off season. What is your experience with these? Any suggestions? Really concerned with safety. Link to comment Share on other sites More sharing options...
Baller Dacon62 Posted July 28, 2020 Baller Share Posted July 28, 2020 Never had wear there yet but only get about 60 sets in a season. Canada is not conducive to a long season. Always take boots out of shell and let them dry and keep them out of the Sun. Sounds like you do the same. Maybe your experience with average use is 150 sets/season and you have a higher wear rate?? Link to comment Share on other sites More sharing options...
Baller Killer Posted July 28, 2020 Baller Share Posted July 28, 2020 I probably have about 150 sets on a pair Over 1.5 seasons. No issues. I pull the liners after use and I never keep the ski in the sun. Link to comment Share on other sites More sharing options...
Baller TEL Posted July 28, 2020 Baller Share Posted July 28, 2020 This is my boot 18 months many many sets Link to comment Share on other sites More sharing options...
Baller TEL Posted July 28, 2020 Baller Share Posted July 28, 2020 Took it to a shoe repair guy $15 works great Link to comment Share on other sites More sharing options...
Baller Dacon62 Posted July 28, 2020 Baller Share Posted July 28, 2020 Loosen bottom strap and top bungie before taking boot off help? Link to comment Share on other sites More sharing options...
Baller WoodySkier Posted July 29, 2020 Baller Share Posted July 29, 2020 I always take my boot out to dry, I’m on my 3rd boot in 6 years Link to comment Share on other sites More sharing options...
Baller vtjc Posted July 29, 2020 Baller Share Posted July 29, 2020 I am on my third northern Vermont season on my Carbitex boots. The back of my front boot is breaking down, but the rear boot is holding up well. I loosen and remove my liners each time I take the boots off. I will probably replace the front boot at the start of next season. Link to comment Share on other sites More sharing options...
Baller_ Jody_Seal Posted July 29, 2020 Baller_ Share Posted July 29, 2020 This has been a problem since these types of boots were first introduced. I am now on my 5th or 6th boot since they were introduced and will continue to use them. My carbitex boot also has the back rubber piece rotted out, yet the rest of the boot looks brand new. I punched some holes, installed brass grommets and laced it back up with black rubber tubing. Also mounted it on a MOB system. Link to comment Share on other sites More sharing options...
Baller ALPJr Posted July 29, 2020 Baller Share Posted July 29, 2020 @vtjc same for me. Dbl boots, 3rd season, about 100 sets total, and diligently cared for. Really like them, and will likely weigh the replacement cost, benefits by this time next year. Link to comment Share on other sites More sharing options...
Baller Zman Posted July 29, 2020 Baller Share Posted July 29, 2020 Dang! @Jody_Seal That's some pretty awesome work. Maybe @brooks should incorporate that into the next model year boots. If the tubing begins to break down, just re-tube! Link to comment Share on other sites More sharing options...
Baller UWSkier Posted July 29, 2020 Baller Share Posted July 29, 2020 This boot has three full seasons on it and looks the same as the day I got it (never used this liner). This was a replacement for a torn 2016 model (the orange and black ones). How tight are you cinching down the laces? I just put 2020s on my ski but think I'll keep this as a spare. BTW flex tape works awesome for repairing these when they tear. Have a few buddies who are several years on repaired ones that function as new. Link to comment Share on other sites More sharing options...
Baller matt_b Posted July 29, 2020 Author Baller Share Posted July 29, 2020 Thanks for all the comments. Like I said this is my 3rd pair and they have all fallen apart at the same exact areas. I actually wear a 10, but use a 11 just because they feel better on the width. And for safety I never clinch them tight. Dislocated knee, 10 years ago. I really try to be gentle with them, but it sure looks like its a common issue for most. I'm embarrassed to post a pic of them now, but I am still using them, hopefully last the rest of the season. Just seems for 650 bucks a pair they should last longer. Link to comment Share on other sites More sharing options...
Baller BraceMaker Posted July 29, 2020 Baller Share Posted July 29, 2020 Make sure to really open up the lacers fully before getting them on too don't want to push in too hard. Had a pair of more adjustable ones on the boat ski and a moose of a cousin blew out the back trying to cram his size 13 paw in there. Link to comment Share on other sites More sharing options...
Baller skierjp Posted July 29, 2020 Baller Share Posted July 29, 2020 I get 3 years out of mine and never remove the liners. Florida skier! When done I rinse the ski and bindings with clean water and fan dry. Shoe size 10 and binding size 10. I always wet bindings first before putting my foot in. Mine split down the middle in the back. Link to comment Share on other sites More sharing options...
Baller Chef23 Posted July 30, 2020 Baller Share Posted July 30, 2020 I never remove the liners from mine either. I loosen all the laces and slide my foot out of the binding. I leave the binding open in my shed to dry. I am a twice a week at most skier and frankly haven’t been skiing very hard but my boot still looks great. Link to comment Share on other sites More sharing options...
Baller thager Posted July 30, 2020 Baller Share Posted July 30, 2020 I have boots going back to 2009. No failures. How many people are using soap to put their boots on? Can't be good for the rubber.For older boots out of warranty boots wish there was an option to buy the rubber heel pieces. Link to comment Share on other sites More sharing options...
Baller vtjc Posted July 30, 2020 Baller Share Posted July 30, 2020 This is what the back of my front boot looks like after the 2017, 2018, 2019 and half of the 2020 season. I take my feet out with the liners after each set, and let them dry. I never use soap. The back of my rear boot looks like new. I will likely replace the front boot at the start of next season. Link to comment Share on other sites More sharing options...
Baller skierjp Posted July 30, 2020 Baller Share Posted July 30, 2020 Looks like you are pulling on the rubber to put your boot on? Link to comment Share on other sites More sharing options...
Baller skierjp Posted July 30, 2020 Baller Share Posted July 30, 2020 The typical failure is a spit down the center of the rubber in the back Link to comment Share on other sites More sharing options...
Baller buoyboy1 Posted July 30, 2020 Baller Share Posted July 30, 2020 I had the same issues with mine after only 4 or 5 months. I really think they had a bad batch come through. Radar and there great customer service was willing to replace mine. I have had my replaced pair for well over a year with zero issues. I always take the liners out and my ski stays covered and out of the sun when not in use. One trick for placing liners back in the shell is to cut out some flexible clear drafting table type sheet vinyl in the exact shape of your shell footbed (place the vinyl under the shell and trace it out). The liner will slip into the shell a lot easier and take stress off the rear rubber. I also slightly wet the bottom of liner as well. Link to comment Share on other sites More sharing options...
Baller vtjc Posted July 30, 2020 Baller Share Posted July 30, 2020 @skierjp I don't grab the rubber putting my foot in the liner. But good thought. I got great support from Radar on an issue I had with the Carbon/G10 plate. Link to comment Share on other sites More sharing options...
Baller skierjp Posted July 30, 2020 Baller Share Posted July 30, 2020 I wonder if you had the same problem I had? Screws pulled through the plate Link to comment Share on other sites More sharing options...
Baller vtjc Posted July 30, 2020 Baller Share Posted July 30, 2020 @skierjp that was my issue. It is clear Radar updated the plate to resolve the issue going forward. Link to comment Share on other sites More sharing options...
Baller Lars Posted August 2, 2020 Baller Share Posted August 2, 2020 I've heard silicon spray can help prevent dry rot of rubber, maybe spraying some on the back part of the boot from time to time could help? Link to comment Share on other sites More sharing options...
Baller S1Pitts Posted August 2, 2020 Baller Share Posted August 2, 2020 I use the products for maintaining the latex seals on drysuits. Treat the boot rubber ever few weeks. Also use a long wide plastic shoe horn to slide in liner and use it to slip my feet into a dry liner when skiing. 2011 Strada boots that still look like new. Link to comment Share on other sites More sharing options...
Baller matt_b Posted August 6, 2020 Author Baller Share Posted August 6, 2020 Thanks for all the input. It seems that people's experience is either No problems or total fail. Like I said this is pair number 3. Is the Pulse comparable? What will I be giving up in performance if anything? I went to a 11 in the Carbitex somewhat to give me more room side to side for my foot width. I read on another post that the Pulse is a bit wider. @brooks ? Don't think any shops in Austin have any to try on for size. Link to comment Share on other sites More sharing options...
Baller Zman Posted August 6, 2020 Baller Share Posted August 6, 2020 @thager I always use soap, a couple sprays of diluted soap, to make it easy to slide my feet in (and, help save wear on the liner). Never had any issues with the rubber. I also keep the top laces a bit loose, especially on the back boot. Not sure that helps save the rubber, but I like knowing my feet will come out if needed. Lower laces are snug with the BOA. Link to comment Share on other sites More sharing options...
Baller thager Posted August 6, 2020 Baller Share Posted August 6, 2020 @Zman Depends on the kind of soap I guess. Some like Dawn are quite caustic, others not so much. More than likely a combo of causes like acid or basic water, soap, too small boot, removing and replacing liner, sun, bad manufacture etc. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now